Kyoto University Graduate School of Engineering Department of Micro Engineering
Machining Measurement and Control Laboratory

Alumni

This list shows alumni of our group since 1996. The second line shows his research topic for his thesis. Note that, for example, a 1996 graduate means that his/her graduation date is March of 1997.

2012 Ph. D. GRADUATE

Koike, Yusuke
Research on Machining Process Design of Difficult-to-cut and Low-stiffness Workpiece

2012 M. S. GRADUATE

Ota, Yusuke
A machining test for identifying error motions of 5-axis machining center

Kimura, Yoshihiro
On-machine Measurement Using Laser Displacement Sensor under Simultaneous Five-axis Control of Target Position and Orientation

Sakai, Taku
Analysis of Frictional Property of Rolling Guideway with Sliding Concept

Sato, Goh
The Measurement Method of Volumetric Errors of Machine Tools Based on The Triateration Principle

Maeda, Minetaka
Chatter Suppression in Turning Operation with Compliance Control using Piezoelectric Device

2012 B. S. GRADUATES

Enjuji, Keigo
Research on Vibration Characteristics between Tool and Workpiece

Nishioka, Yuichiro
Research on Positional Deviation in Feed Direction of Ball Screw Feed Drive System

Matsunaga, Naoki
Analysis of Vibration Characteristics of Rolling Guide

Yamada, Takashi
Evaluation of SPH Simulation by Comparing with Machining Experiment

2011 P h. D. GRADUATE

Fujita, Tomoya
Development of High-precision Feed Drive System

Hong, Cefu
Error Calibration on Five-axis Machine Tools by Relative Displacement Measurement between Spindle and Work Table

2011 M. S. GRADUATE

Ikenaga, Shinya
Non-contact Magnetic Loader to Measure Spindle Stiffness

Inagaki, Takahiro
A Study on Influence of Contact Stiffness on Support Stiffness of Machine Tools

Kudo, Tomoya
Estimation of Three-dimensional Volumetric Errors of Numerically Controlled Machine Tools by a Laser Tracker

Shida, Kosuke
Accuracy Enhancement of End milling for Flexible Parts

2010 M. S. GRADUATE

Oyama, Chiaki
Measurement of motion errors on 5-axis machine tool by R-test

Tanizawa, Yusuke
Vision-based Measurement of Two-Dimensional Motion Errors of a Machine Tool

Takeuchi, Kunitaka
Estimation of Three-dimensional Volumetric Errors of Numerically Controlled Machine Tools by a Laser Tracker

Nakade, Syo
Analysis of machining error in high speed shaper cutting with single crystal diamond tool

Visiting Student (Oct. 2009 - May 2010)

Pit Pillatsch
Vibration Analysis Methods for High-Speed, High-Precision Machine Tools using Rigid Body Simulation

2010 B. S. GRADUATES

Yamada, Shimpei
Analysis of friction force in linear rolling guideway by multi bristle model

2009 P h. D. GRADUATE

Kono, Daisuke
Identification of Copying ratio of Tool Edge Motion by using Measurement-fused Machining System

2009 M. S. GRADUATES

Iritani, Takeyuki
Error calibration for 5-axis controlled machine tools based on on-machine geometric measurement of artifact

Tsuchida, Kohei
Analysis of Cutting Phenomenon of Micromilling by using Small Endmill

Hirooka, Takahiko
Analysis of Disturbance Vibration in High Precision Machining

Visiting Student (Sep. 2009 - Mar. 2010)

Karl-Robert Deibel
Modeling and Diagnosis of the Dynamic Synchronous Errors of Contouring Control of Machine Tools

2009 B. S. GRADUATES

Yoshino, Fumiya
Prediction of Natural Frequency Change of Workpiece in Cutting

2008 M. S. GRADUATES

Iizuka, Atsushi
Improvement of contouring accuracy in multi-axis synchronized motion

Shimizu, Takuya
Control of tool life in end milling processes

Hata, Takafumi
Estimation of three-dimensional volumetric accuracy using laser measurement

Hirono, Yoko
Design of a micro-cutting machine tool with vibration rejection and control

2008 B. S. GRADUATES

Sakaguchi, Taisuke
Development of a magnet loader for rotating spindles

Kadowaki, Seishiro
On micro-slotting by miniature end mills

2007 P h. D. GRADUATE

Uddin, Mohammed Sharif
Tool path modification approaches to enhance machining geometric accuracy in 3-axis and 5-axis machining

2007 M. S. GRADUATES

Nakatsukasa, Yosuke
On the Machining of Co-Cr-Mo Alloys

Sawada, Masahiro
A Machining Test to Identify Kinematic Errors on Five-axis Machine Tools

Anazawa, Yuichi
Motion Error Analysis of a High-precision Machine Tools with Non-contact Drives

2007 B. S. GRADUATES

Kusama, Ryoichi
Electric Manuals for Assembly Processes

2006 P h. D. GRADUATE

Diaa Sarhan, Ahmed Aly
Estimation of Cutting Forces from the Spindle Displacement

2006 M. S. GRADUATES

Hatozaki, Takashi
On High-precision Ball-screw Driven Feed Drives

Kono, Daisuke
Development of a High Precision Machine Tool with Measurement References

Sugihara, Motoyuki
Measurement of Spindle Stiffness on Machine Tools

2005 M. S. GRADUATES

Yasuda, Tomohiro
Estimation and control of cutting forces in end milling processes

2004 M. S. GRADUATES

Okuda, Toshihiro
Compensation of motion errors on a parallel kinematic machine tool

Yokawa, Takeshi
Calibration of kinematic errors on multi-axis machine tools

2003 P h. D. GRADUATES

Lee, Kangyu
A study on improvement of motion accuracy of feed drive in NC machine tools by vibration control

2003 M. S. GRADUATES

Ikeda, Daisaku
High-accuracy die/mold machining by constant engagement tool path generation

Uebayashi, Koji
Automated tuning of servo parameters based on the measurement of contouring errors

Sakahira, Masahiro
Monitoring and control of cutting forces in end milling

Tanaka, Takuya
Improvement of positioning accuracy of feed drives by vibration control

Visiting Student (Sep. 2001 - Oct. 2003)

Tang, Ying, Dr.
Optimal Machining Process Planning based on Canned Cycles

2003 B. S. GRADUATES

Ishii, Masahiro
High-accuracy control of ball-screw driven feed drives

Nimura, Kazunori
Suppression of base vibration by dual actuation

Maeda, Daisuke
In-process optimization of cutting conditions and tool paths in canned end milling cycles

2002 M. S. GRADUATES

Adachi, Yoshiki
The effect of cutting temperature on tool life in die and mold machining

Umemoto, Masashi
Vibration control on a feed drive of NC machine tools

Takaoka, Hiroya
Compensation of gravity-induced motion errors on parallel-mechanism machine tools

Fujita, Yoshifumi
Optimal machining process planning for end milling processes in part production

2002 B. S. GRADUATES

Inoue, Daisuke
Tool path planning using trochoid cycles for die and mold manufacturing

Oda, Yoshihiro
The monitoring of cutting forces by using a displacement sensor

Shiraishi, Yuya
A variable-friction guideway for the damping control of feed drive systems

2001 M. S. GRADUATES

Endo, Masaya
An intelligent guide for damping control of feed drive systems

Ogawa, Takashi
Adaptive force Control for milling processes

Nohara, Masashi
Cutting force control in die and mold manufacturing

Visiting Student (Sep. 2001 - Mar. 2002)

Wang, Weili
Optimal Machining Process Planning based on Canned Cycles

2001 B. S. GRADUATES

Ioka, Seisuke
Tool life prediction in die/mold machining

2000 M. S. GRADUATES

Owaki, Satoshi
Analysis and compensation of stick motion

Tsuda, Naoki
CAM systems for die/mold manufacturing

2000 B. S. GRADUATES

Ishida, Takahiro
Calibration method for parallel mechanism machine tools

Okazawa, Hiroshi
Tool life estimation in milling processes

Okamoto, Keiji
An intelligent guide for damping control of feed drive systems

Nakae, Hirokazu
Unified end milling process simulator

2000 Ph. D. GRADUATE

Schramm, Andre
An intelligent CAM system for die and mold making (ICAMS)

1999 Ph. D. GRADUATE

Lin, Shuding

1999 M. S. GRADUATES

Hsiao, Shih-Hsiu

Kamatani, Koji

1999 B. S. GRADUATES

Uozumi, Hideki

Kanamori, Kaya

Watanabe, Yasushi

1998 M. S. GRADUATES

Ogawa, Daisuke

Sasaki, Masashi

1998 B. S. GRADUATES

Onishi, Hidetomo

Hashimoto, Takaaki

Anada, Mayumi

Kondo, Masataka

Sakurama, Kazunori

1997 M. S. GRADUATES

Morioka, Tokuhiro

1996 M. S. GRADUATES

Ogino, Takashi

Prakosa, Tri

1996 B. S. GRADUATES

Tsuji, Atsushi

Wada, Astuyuki

Matsuyama, Satoru

Yamashita, Koichiro